Reward Points
:
1648
£1,978.31
£1,648.59
Testo 300LL Long-life Flue Gas Analyser with NOx Sensor & Printer
The Testo 300LL Smart Long-life Flue Gas Analyser with NOx Sensor is optimised for servicing commercial boilers. To this end, it includes a NO sensor with a range of 0 to 3000ppm, as well as a H₂-compensated CO sensor with automatic dilution to 30, 000ppm. In addition to this, the Testo 300LL Smart Long-life Flue Gas Analyser with NOx Sensor features an O₂ sensor capable of measuring oxygen levels between 0 and 21 vol.%; this analyser is also capable of measuring the following parameters:
- Draught: -9.99 mbar to +40 mbar
- Pressure: -100 mbar to +200 mbar
- Temperature: -40°C to 1200°C
The inclusion of a NO (nitric oxide) sensor and an adjustable NO₂ (nitrogen dioxide) pre-set value enables this Testo 300LL Smart Long-life Flue Gas Analyser’s ability to determine the total NOx (nitrogen oxide) measurement; this reading can be converted into an mg/kWh value for direct comparison with the emission levels specified in the ErP directive.
In September 2018, a new phase in the ErP directive specified the maximum permissible NOx emission levels for all 400kW-rated, domestic and commercial heating and hot water units. It specifies the following levels:
- 56 mg/kWh for gas- and LPG-fired boilers
- 120 mg/kWh for oil-fired boilers
The Testo 300LL Smart Long-life Flue Gas Analyser with NOx Sensor, which has been designed and tested in accordance with EN 50379 Parts 1-3, provides a solution to maintaining compliance with the above requirements.
Via the addition of various optional probes and accessories, the Testo 300LL Smart Long-life Flue Gas Analyser with NOx Sensor can be used to measure differential temperature, gas flow pressure and ambient CO. It can also be used to perform gas pipe tests and may be used to check flue gas pipes with larger diameters via the addition of an OPTIONAL longer probe shaft, and can test units in difficult-to-access places using an OPTIONAL flexible probe. The Testo 300LL Smart Long-life Flue Gas Analyser’s multi-functional handle allows the user to attach a variety of quick-change probe shafts (sold separately) in order to tailor the analyser to the application.
Moreover, the Testo 300LL Smart Long-life Flue Gas Analyser with NO sensor features extra-strong magnets allowing the engineer to attach the unit to a magnetic surface to be held in place throughout the testing procedure, thereby freeing his/her hands. This improves the ease and efficiency of conducting the necessary tests.
Measurements and parameters can be viewed via the 5-inch HD display. It is easy to access the necessary settings, parameters, records and readings using the Testo 300LL Smart Long-life Flue Gas Analyser’s smart-touch display and clearly structured menus. This analyser has the same response time as a smartphone or tablet; for further information regarding the Testo 300LL Smart Long-life Flue Gas Analyser’s smart-touch display; please see the following video.
testo 300 Flue Gas Analyser
The Testo 300LL Smart Long-life Flue Gas Analyser’s screen is replaceable, recessed and scratch-proof; it is covered by a replaceable, protective film. This instrument is housed in a protective, robust, rubber casing making it suitable for use in rugged environments and improving the unit’s longevity.
Also working to extend this unit’s longevity, as well as decrease the instrument’s downtime and maintenance costs, is its automatic sensor protection. This feature ensures that Testo 300LL Smart Long-life Flue Gas Analyser’s sensors will not need replacing for at least five years*, this reduces the long-term costs of the unit both with regards to part replacement and lost earnings caused by necessary downtime.
Downtime in between applications is also reduced when the Testo 300LL Smart Long-life Flue Gas Analyser is placed in Standby mode as the user does not need to wait for the completion of the zeroing phase before he/she can re-commence testing. Moreover, its integrated rechargeable battery is able to supply up to ten hours of power, reducing the frequency with which it needs to be recharged and thereby also decreasing downtime.
Additionally, as this Testo 300LL Smart Long-life Flue Gas Analyser with NO Sensor features the functionality of a smartphone or tablet, it can be used to create reports onsite which can be emailed to clients via a WLAN interface. Alternatively, as this instrument includes a signature function the engineer and client are able to sign the custom report onsite, thereby increasing efficiency and convenience as well as reducing paperwork.
Reports, readings and client information can be saved to the Testo 300LL Smart Long-life Flue Gas Analyser’s extensive 32GB memory; it is able to accommodate up to 5000 readings and multitudinous customer details such as contact information, boiler type, site records and retest dates. The Testo 300LL Smart Long-life Flue Gas Analyser’s sophisticated user-interface will alert the engineer when a customer’s asset is due for re-inspection.
Information saved to the Testo 300LL Smart Long-life Flue Gas Analyser with NO Sensor can be transferred to the user’s PC and organised using the supplied Testo EasyHeat PC Analysis Software; this software can also be used to configure the Testo 300LL Smart Long-life Flue Gas Analyser with NO Sensor.
It is also possible to transfer readings, reports and data to an industry- or customer-specific software program. ** Alternatively, the engineer may print readings onsite using the supplied Testo Infrared/ Bluetooth Printer and the Testo 300LL Smart Long-life Flue Gas Analyser’s Bluetooth® interface.
The Testo 300LL Smart Long-life Flue Gas Analyser with NO Sensor is a comprehensive, cost-effective and convenient instrument optimised for servicing commercial boilers and maintaining compliance with relevant regulations.
PASS Presents the Combustion Analyser Showdown - Testo 300 vs Testo 327
Testo 300 or 327 Flue Gas Analysers: Which One to Choice?
Testo 300LL Smart Long-life Flue Gas Analyser with NO Sensor Key Features
- Optimised for servicing boilers
- NO sensor: 0 to 3000ppm
- CO Sensor (H₂ compensated): 0 to 8000ppm
- CO Sensor (H₂ compensated) with automatic dilution: 0 to 30 000ppm
- O₂: 0 to 21 vol.%
- Draught: -9.99 mbar to +40 mbar
- Pressure: -100 mbar to +200 mbar
- Temperature: -40°C to 1200°C
- Adjustable NO₂ pre-set value
- Calculates the total NOx
- Convert NOx measurements into mg/kWh values for easy comparison to the limits specified in the ErP directive
- Designed and tested in accordance with EN 50379 Parts 1-3
- Perform additional tests by attaching various OPTIONAL probes and accessories
- Differential temperature measurement (OPTIONAL)
- Gas flow pressure measurement (OPTIONAL)
- Ambient CO measurement (OPTIONAL)
- Gas pipe testing (OPTIONAL)
- Multi-functional handle for attaching quick-change probes (sold separately)
- Attach an OPTIONAL longer probe shaft to measure flue gas pipes with larger diameters
- Attach an OPTIONAL flexible probe to check units in hard-to-reach places
- Extra-strong magnets
- 5-inch HD display
- View the relevant parameters and measurements via the display
- Smart-touch display
- Clearly-structured menus
- Has the same response time as a smartphone or tablet
- Recessed, scratch-proof screen covered by a protective film
- Protective film and screen are replaceable
- Protective, robust, rubber casing
- Automatic sensor protection
- Automatic sensor protection reduces the frequency with which sensors need to be replaced
- Automatic sensor protection reduces downtime and maintenance costs
- It is anticipated that the sensors will not need replacing for at least five years*
- Standby mode: no need to wait for the completion of the zeroing mode
- Integrated, rechargeable battery provides up to ten hours of power
- Create onsite reports
- Signature function
- Email reports to clients via a WLAN interface
- 32GB memory
- Save up to 5000 readings, reports and customer details
- Alerts the user when a customer’s asset is due for re-test
- Transfer saved information to a PC
- Organise data using the supplied Testo EasyHeat PC Analysis Software
- Transfer data to an industry- or customer-specific software program**
- Print readings on-site via the analyser’s Bluetooth® interface and using the supplied Testo Infrared/ Bluetooth Printer
- A comprehensive, convenient and cost-effective analyser
- Optimised for servicing commercial boilers and maintaining compliance with the relevant regulations
What’s Included?
| Product | Kit | |||
|---|---|---|---|---|
| Code | Name | 0564300482 Standard |
0564300489 + Printer |
0564300484 + NOx & Sensor Printer |
| 0633 3004 88 | Testo 300 Long Life Analyser | ✓ | ✓ | ✓ |
| NOx Sensor | - | - | ✓ | |
| 0554 1105 | USB Mains Unit with Cable | ✓ | ✓ | ✓ |
| 0600 9760 | Compact Basic Flue Gas Probe | ✓ | ✓ | ✓ |
| 0554 3385 | 10x Spare Dirt Filters with Compact Probes | ✓ | ✓ | ✓ |
| 0554 3332 | Testo Easyheat Analysis Software | ✓ | ✓ | ✓ |
| 0516 3300 | Carry Case | ✓ | ✓ | ✓ |
| 0554 0621 | Bluetooth/ IRDA Printer | - | ✓ | ✓ |
| 0554 0568 | Spare Thermal Paper with Indelible Ink | - | ✓ | ✓ |
| View | View | View | ||
* An approximate determined based on the analyser being in normal service
**Please Note: the manufacturer has to integrate an interface into the industry software to use the function
Free Testo Organiser
Get a Free Testo Heavy Duty Organiser with your purchase to securely store and organise your tools. This durable organiser keeps everything easily accessible and well-protected.
Free Pipe Cutters & Brushes
- 15mm + 22mm AutoCut Pipe Cutters, Water Pump Pliers & 4 Way Multi-Tool - FGAPROMO2, typically £45.00
Testo 300LL Smart Long-life Flue Gas Analyser with NOx Sensor Technical Specifications
| Measurement Parameter | Measuring Range | Accuracy (±1 Digit) | Resolution |
| O₂ measurement | 0 to 21 vol.% | ±0.2 vol.% | 0.1 vol.% |
| CO measurement (without H₂ compensation) | 0 to 4,000 ppm | ±20 ppm (0 to 400 ppm) | 1 ppm |
| ±5% of m.v. (401 to 2,000 ppm) | |||
| ±10% of m.v. (2001 to 4,000 ppm) | |||
| CO measurement (with H₂ compensation) | 0 to 8,000 ppm | ±10 ppm or ± 10% of m.v. (0 to 200 ppm) | 1 ppm |
| ±20 ppm or ± 5% of m.v. (201 to 2,000 ppm) | |||
| ±10% of m.v. (2,001 to 8,000 ppm) | |||
| CO measurement (with H₂ compensation and dilution) | 0 to 30,000 ppm | ±100 ppm or ± 10% of m.v. | 1 ppm |
| Combustion ratio (calculated) | - | - | 0.0001 |
| NO measurement | 0 to 3000 ppm | ±5 ppm (0 to 100 ppm) | 1 ppm |
| ±5% of m.v. (101 to 2,000 ppm) | |||
| ±10% of m.v. (2,001 to 3,000 ppm) | |||
| Efficiency testing (Eta) | 0 to 120% | - | 0.1% |
| Flue gas loss | 0 to 99.9% | - | 0.1% |
| CO₂ determination (digital calculation from O₂) | Display range 0 to CO₂ max. | ±0.2 vol.% | 0.1 vol.% |
| Draught measurement | -9.99 to +40 mbar | ±0.005 mbar (0 to 0.1 mbar) | 0.001 mbar (0 to 0.1 mbar) |
| ±0.02 mbar (0.1 to +3.00 mbar) | 0.01 mbar (remaining meas. range | ||
| ±1.5% of m.v. (+3.01 to +40 mbar) | |||
| Pressure measurement | -100 to 200 mbar | ±0.5 mbar (0 to +50.0 mbar) | 0.01 mbar |
| ±1% of m.v. (+50.1 to +100.0 mbar) | |||
| ±1.5% of m.v. (+100.1 to +200 mbar) | |||
| Temperature (instrument) | -40 to +1,200°C | ±0.5°C (0.0 to +100.0°C) | 0.1°C (-40 to +999.9°C) |
| ±0.5% of m.v. (remaining meas. range) | 1°C (remaining meas. range) | ||
| Ambient CO measurement (internal/flue gas probe) | 0 to 2,000 ppm | ±10 ppm (0 to 100 ppm) | 1 ppm |
| ±10% of m.v. (101 to 2,000 ppm) | |||
| Ambient CO measurement (external with CO probe) | 0 to 500 ppm | ±3 ppm (0 to 29 ppm) | 1 ppm |
| ±10% of m.v. (30 to 500 ppm) | |||
| General Technical Data | |||
| Certification | The testo 300 is TÜV-tested according to 1st German Federal Immission Control Ordinance (BImSchV) EN 50379, Parts 1-3 | ||
| Storage temperature | -20 to +50°C | ||
| Operating temperature | -5 to +45°C | ||
| Charging temperature | 0 to +45°C | ||
| Humidity application range | 15 to 90% RH, not condensing | ||
| Power supply | Rechargeable battery, USB mains unit | ||
| Rechargeable battery life | 10 hrs | ||
| Protection class | IP 40 | ||
| Memory | 1 mio. measurement values | ||
| Display | 5.0" touch display, HD 1280x720 pixels, IPS (160 k) | ||
| Weight | Approx. 800 g | ||
| Dimensions | L: 244 mm (including probe connection) H: 59 mm W: 98 mm | ||
| testo 300 Longlife warranty |
Instrument/probe/gas sensors O₂, CO sensor 48 months NO sensor 24 months Thermocouple and rechargeable battery 12 months |
||
| Warranty terms | https://www.testo.com/en/Guarantee/guarantee | ||
Accessories related to this product:
Reviews
Additional Information
| SKU | 0564300484 |
|---|---|
| Manufacturer Part Code | 0564 3004 84 |
| Country of Origin | Germany |
