Important Notice
This item is made-to-order exclusively for you once your order is placed. As a result, it is not eligible for cancellation or return under our standard policy. Your statutory rights remain unaffected.
Fluke Networks LinkIQ Duo Wi-Fi Cable & NetworkTester
- Internal antenna for Wi-Fi radio
- Large, colour, touchscreen display
- Save up to 1000 results
SKU
LIQ-DUO-KIT-H6-UK
MPN
LIQ-DUO-KIT-H6-UK
The Fluke Networks LinkIQ Duo Cable+Wi-Fi+Network Tester combines cable, network, and Wi-Fi 6E analysis. It verifies cable performance up to 10 Gb/s, and it conducts cable tests, network diagnostics, and Wi-Fi analysis. The LinkIQ Duo measures cable length, detects faults such as opens and shorts, and generates a wire map to pinpoint miswires and split pairs. IEEE-compliant PoE verification ensures accurate power measurements by identifying the PoE class (1-8) and performing load tests.
The LinkIQ Duo utilises the built-in Wi-Fi 6E analysis to scan networks, channels, and access points, identifying configuration issues such as channel overlap, security weaknesses, and illegal channel use (where regulations apply). The nearest switch diagnostics feature provides the IP address, port/VLAN details, and advertised data rates. The LinkIQ Duo is USB-C rechargeable and compatible with LinkWare PC.
Fluke Networks LinkIQ™ Duo Cable+Network+Wi-Fi Tester
Key Features
- Internal antenna for Wi-Fi radio supporting 2.4 GHz, 5 GHz, and 6 GHz bands
- Copper cable tester for installing and troubleshooting network systems
- Verify the performance of copper cables up to 10G
- Ascertain how fast networks run over cabling
- Determine whether cabling can support a specific service
- Check that the system is connected correctly
- Generates test signals via an RJ45 port
- Generates signals in the data frame format of the service you are testing
- Checks signals reach the opposite end in a useable state
- Provides a signal speed reading
- IP ping provides the nearest switch diagnostics
- PASS/FAIL assessment
- Test TCP/IP network connection
- Test copper cable links up to 305m
- Get a wire map of pairs and distances to faults such as opens, shorts, and unterminated
- Detect PoE classes (1-8)
- Perform load tests of available PoE from the connected switch
- Verify gateway and DNS server responsiveness and availability
- Use with the IntelliTone Probe to locate cables
- Analogue and digital toning
- Port blink
- 1x authentication
- Large, colour, touchscreen display
- Save up to 1000 results
- USB-C port for exporting data, updating software, and charging
- Organise data and create reports using Fluke Networks LinkWare PC Software
- Rechargeable Li-Ion battery
- Perfect for installing and troubleshooting copper cable networks
What's Included?
- LIQ-DUO-KIT-H6-UK
- LinkIQ Duo
- Remote IDs #1-7
- IntelliTone Pro 200 probe
- Quick reference guide
- USB-C to USB-A cable
- Charging cable
- Cat6A patch cord
- RJ45/11 modular adapter
- Hanging strap with Remote ID holder
- Carrying case
Technical Information
Specification
| General Specifications | |
|---|---|
| Languages supported in UI | English, German, French, Japanese, Spanish, Thai, Traditional Chinese, Simplified Chinese, Korean, Russian, Italian, Portuguese, Czech, Danish, Dutch, Finnish, Norwegian, Polish, Swedish, and Turkish |
| Weight | 1 lb 6 oz (624g) |
| Battery | Type: Lithium-ion, 3.6 V, 6400 mAh Life: 8 hours typical Charge time: 4.5 hours Charging temperature range: 0 °C to +40 °C |
| Power Adapter | Input: 100 to 240 V ac ±10%, 50/60Hz Output: 15 V dc, 2 A maximum Class II |
| Host Interface | USB type C |
| Display | 800 x 480 colour capacitive multi-touch |
| Dimensions | 22 cm x 11 cm (8.5 in x 4.5 in) |
| Operating Temperature | 0 °C to 45 °C (32 °F to 113 °F) |
| Storage Temperature | -10 °C to 60 °C (-14 °F to 140 °F) |
| Operating Relative Humidity | 0 % to 90 %, 0 °C to 35 °C 0 % to 70 %, 35 °C to 45 °C |
| Operating Altitude | 4,000 m, 3,200 m with AC adapter |
| Vibration | Random, 2 g, 5 Hz-500 Hz |
| Drop | 1 m drop with six sides |
| Active Network Diagnostics | |
| Diagnostic Protocols | Link Layer Discovery Protocol (LLDP), Cisco Discovery Protocol (CDP), Fast Link Pulses (FLP), Internet Control Messaging Protocol (ICMP), and Dynamic Host Configuration Protocol (DHCP) |
| IP Address Setup | LinkIQ address, DNS Server, Gateway for IPv4 or v6 either manually or via DHCP. |
| IP Ping Test Results | Four response time results for target, DNS Server(s), Gateway, plus average and number lost. |
| Nearest Device Diagnostics (If available through diagnostic protocols) |
Switch Name / IP + MAC Address, Port Number, VLAN Name, Advertised Data Rates, Advertised Duplex |
| Power Over Ethernet Compatibility | Ethernet Alliance Certified to IEEE 802.3af/at/bt, Hardware negotiation with signature resistance, Software negotiation with LLDP/CDP |
| Power Over Ethernet Diagnostics | Advertised Power Class (0-8), Advertised Available Power, Powered Pairs, Diagnostics for both Single and Dual signatures |
| Power Over Ethernet Measurements | Loaded Voltage (V), Loaded Power (W) |
| Port Blink | Blink the light of the connected port |
| Cable Test Specifications | |
| Test Port | Shielded 8-pin modular jack accepts 8-pin modular (RJ45) plugs |
| Commissioning Autotests | 10GBASE-T, 5GBASE-T, 2.5GBASE-T, 1000BASE-T, 100BASE-TX, 10BASE-T, Wire map Only. Test Speed: 6 seconds for lengths < 70 m |
| Cable Types | Balanced twisted-pair cabling Unshielded twisted-pair Screened twisted-pair 2-pair and/or 4-pair |
| Wire Map-Only Tests | Document wire map, Length of each pair, diagnose split pairs, user-selectable T568A or T568B, user-selectable crossover settings(Straight through, Half-crossover, Full-crossover). Test speed: 1 second for lengths < 120 m |
| Length (Maximum) | 305 m (1000 ft) |
| Nominal Velocity of Propagation (NVP) | User settable |
| Tone Generator | Generates digital tones compatible with Fluke Networks's IntelliTone probe. Generates analogue tones compatible with general analogue probes. |
| Remote ID Locators | Use remote ID terminations to identify up to 7 unique ports or office outlets. |
| Wi-Fi Test Specifications | |
| Supported Wireless Standards | 802.11b, 802.11a, 802.11g, 802.11n (Wi-Fi 4), 802.11ac (Wi-Fi 5), and 802.11ax (Wi-Fi 6/6E). Additionally, the tester will report the presence of future standards, such as 802.11be, if the standard's presence can be decoded in a supported beacon. |
| Frequency Supported | Frequencies of channels received and transmitted (where allowed by country regulations): 2.4 GHz band: 2.402 to 2.482 GHz (channel 1 to channel 13); 5 GHz band: 5.170 to 5.330 GHz, 5.490 to 5.730 GHz, 5.735 to 5.835 GHz (channel 36 to channel 165); 6 GHz band: 5.945 to 7.125 GHz (channel 1 to channel 233). NOTE: The tester transmits only on the frequencies allowed in the country where it is sold. |
| Country Certifications | AE, AU, AR, BR, CA, CL, CN, IN, JP, KR, KW, MY, MX, NZ, PH, SG, TH, TW, UK, US, ZA, plus the European Union (Completed or in process. Contact your local Fluke representative for details.) |
| Network Tests | Number and name (BSSID) of available access points, signal strength, security type, IEEE 802.11 standard supported |
| Access Point Tests | Networks supported / country code, BSSID, signal strength, band/channel/bandwidth, IEEE 802.11 standards supported, security types, TX/RX rates |
| Channel Tests | Utilization, Number/signal strength of access points, overlap |
Document Downloads
Additional Information
SKU
LIQ-DUO-KIT-H6-UK
Manufacturer Part Code
LIQ-DUO-KIT-H6-UK
Fluke Networks LinkIQ Duo Wi-Fi Cable & NetworkTester
£3,500.00
£4,200.00 inc vat
£3,500.00
£4,200.00 inc vat