Important Notice
This item is made-to-order exclusively for you once your order is placed. As a result, it is not eligible for cancellation or return under our standard policy. Your statutory rights remain unaffected.
Aim-TTi I-Prober 520 Positional Current/Field Probe
- High-accuracy, general-purpose H-field probe
- Wide dynamic range: 10mA to 20A peak-to-peak
- Attach to any oscilloscope
SKU
58250-0010
MPN
58250-0010
The Aim-TTi I-Prober 520 Positional Current/Field Probe is a high-accuracy, general-purpose H-field probe that can be converted into a ‘closed magnetic circuit’ current probe. It is compatible with all oscilloscopes and is suitable for measuring currents in PCB tracks, as well as captive wires into components, legs of integrated circuits, and PCB ground planes. The Aim-TTi I-Prober 520 Positional Current/Field Probe is appropriate for use on high-voltage conductors and in high-temperature areas as well as confined and difficult-to-access spaces.
Currents from DC up to 5MHz can be observed and measured by placing the insulated tip on the conductor. Its low insertion impedance and stray capacitance cause minimal disturbance to the circuit conditions. Moreover, there is no need to break or surround the conductor.
The Aim-TTi I-Prober 520 Positional Current/Field Probe features a wide dynamic range of 10mA to 20A peak-to-peak. It has a safety rating of 300V CAT II (600V CAT I).
The Aim-TTi I-Prober 520 Positional Current/Field Probe is a precise and practical H-field probe.
Aim-TTi I-Prober 520 Positional Current/Field Probe Key Features
- A high-accuracy, general-purpose H-field probe
- Can be converted into a ‘closed magnetic circuit’ current probe
- Can be attached to any oscilloscope
- Measure currents in PCB tracks, capacitive wires into components, legs of integrated circuits and PCB ground planes
- Appropriate for use on high-voltage conductors and in high-temperature areas, as well as confined and difficult-to-access spaces
- Observe and measure currents from DC up to 5MHz
- Place the insulated tip on the conductor
- Low insertion impedance and stray capacitance cause minimal disturbance to the circuit conditions
- No need to break or surround the conductor
- Wide dynamic range: 10mA to 20A peak-to-peak
- Safety rating: 300V CAT II (600V 600 CAT I)
- A precise and practical H-field probe
What’s Included?
- Aim-TTi I-Prober 520 Positional Current/Field Probe
- Power Supply
- Instruction Manual
- Calibration Graph
- Carrying Case
Technical Information
Specification
Aim-TTi I-Prober 520 Positional Current/Field Probe Technical Specifications
| General Specifications | ||||
| Output Signal | Maximum Output | ± 10V | ||
| Oscilloscope Input | Suitable for an input impedance of 1MW in parallel with < 30pF | |||
| Trace Position | Wide range DC offset control within control box. | |||
| Safety | Max. Circuit Voltage | 300V Cat II (on AC line circuits) | ||
| 600V (on uncategorised secondary circuits inside equipment) | ||||
| Max. Tip Temperature | 150ºC maximum allowable temperature at probe tip. | |||
| Conformance | Complies with EN61010-1 & EN61010-031 | |||
| Bandwidth Control | Switch Position | Full | 500kHz | 2Hz |
| Nominal Bandwidth | DC to 5MHz | DC to 500kHz | DC to 2Hz | |
| Risetime | <70ns | 700ns | 175ms | |
| Aberrations | <±5% | <±1% | <±1%. | |
| Noise (Typical)* | 6mA rms | 3mA rms | 1.5mA rms | |
| Note | * This is the noise level for current measurement using the Toroid attachment. For PCB track measurement the equivalent noise will depend upon the track width and gain setting but will be similar to the Toroid measurement figure for a track width of 0.5mm. |
|||
| HF Performance (bandwidth switch at Full) | Propagation Delay | 60ns typical (to 10%). | ||
| Bandwidth | DC to 5MHz (small signal) | |||
| Slew Rate | 15A/µs (equivalent) | |||
| Overload Indication | Indicator Threshold | Indicator LED within control box will light if output voltage exceeds ± 10V or if large magnetic fields cause the system to saturate. | ||
| Power Source | Power Supply | 5.2V at up to 5 watts from AC line adaptor (supplied). | ||
| Mechanical | Probe Dimensions | 155mm x 38mm x 28mm max; 2.8mm x 1.8mm at tip | ||
| Cable Length | 2m from probe tip to output BNC | |||
| EMC | Conformance | Complies with EN61326 | ||
| Magnetic Field Measurement (Mode = Field) | ||||
| Scaling Factor | 250µT (or 200A/m) per Volt. | |||
| Accuracy and Linearity | ±3% | |||
| Maximum Field | ±2·5mT (2000A/m). | |||
| Current Measurement Using Toroid (Mode = Wire) | ||||
| Scaling Factor | 1 Amp per Volt | |||
| Accuracy and Linearity | ±5% | |||
| Current Range | ±10mA to ±10A (DC + peak) | |||
| Max. Wire Diameter | 3.5mm (unbroken) or 6mm (end fed) | |||
| Current Measurement In PCB Tracks (Mode = PCB Track) | ||||
| Scaling Factor | Adjustable to 1 Amp per Volt for track widths 0·2mm to 3.5mm (0·007” to 0·14”) and 2 Amp per volt for track widths 3mm to 6.5mm (0·125” to 0·25”) using Calibrator and compensation graph. |
|||
| Sensor Spacing | 0.7mm distance from sensor to PCB track set by probe design. | |||
| Calibrator | Built-in calibrator within the control box providing an AC or DC calibration current through a 0.5mm track. |
|||
Document Downloads
Aim-TTi I-Prober 520 Positional Current-Field Probe - Datasheet
Aim-TTi I-Prober 520 Positional Current-Field Probe - User Manual
Additional Information
SKU
58250-0010
Manufacturer Part Code
58250-0010
Aim-TTi I-Prober 520 Positional Current/Field Probe
£706.00
£847.20 inc vat
£706.00
£847.20 inc vat